Laboratory Studies to Determine Suitable Chemicals to Improve Oil Recovery from Garzan Oil Field

Garzan oil field is located at the south east of Turkey. It is a mature oil field and the reservoir is fractured carbonate reservoir. After producing about 1% original oil in place (OOIP) reservoir pressure started to decline. Waterflooding was started in order to support reservoir pressure and also to enhance oil production in 1960. Waterflooding improved the oil recovery but after years of flooding water breakthrough at the production wells was observed. This increased the water/oil ratio at the production wells. In order to enhance oil recovery again different techniques were investigated. Chemical enhanced oil recovery (EOR) methods are gaining attention all over the world for oil recovery. Surfactant injection is an effective way for interfacial tension (IFT) reduction and wettability reversal. In this study, 31 different types of chemicals were studied to specify the effects on oil production. This paper presents solubility of surfactants in brine, IFT and contact angle measurements, imbibition tests, and lastly core flooding experiments. Most of the chemicals were incompatible with Garzan formation water, which has high divalent ion concentration. In this case, the usage of 2-propanol as co-surfactant yielded successful results for stability of the selected chemical solutions. The results of the wettability test indicated that both tested cationic and anionic surfactants altered the wettability of the carbonate rock from oil-wet to intermediate-wet. The maximum oil recovery by imbibition test was reached when core was exposed 1-ethly ionic liquid after imbibition in formation water. Also, after core flooding test, it is concluded that considerable amount of oil can be recovered from Garzan reservoir by waterflooding alone if adverse effects of natural fractures could be eliminated.     

中空激光光内送粉熔池温度控制研究

在激光增材制造过程中,熔池温度的稳定性是表征加工过程稳定性的一个重要指标.设计一套控制熔池温度的闭环反馈系统,以达到控制熔池温度,提高成形件质量.基于C#编程软件实现了温度信号的传递,采用PID控制算法设计了温度控制器.实验结果表明,此系统能实时、准确地实现熔池温度的闭环控制,能够有效消除直壁墙熔覆过程中因热累积而造成的“蘑菇云”现象,且成形件几何精度有显著提高,各处显微组织差异较小,组织致密均匀.     

Estimating long-term time-resolved indoor PM2.5 of outdoor and indoor origin using easily obtainable inputs

To evaluate the separate impacts on human health and establish effective control strategies, it is crucial to estimate the contribution of outdoor infiltration and indoor emission to indoor PM_2.5 in buildings. This study used an algorithm to automatically estimate the long-term time-resolved indoor PM_2.5 of outdoor and indoor origin in real apartments with natural ventilation. The inputs for the algorithm were only the time-resolved indoor/outdoor PM_2.5 concentrations and occupants’ window actions, which were easily obtained from the low-cost sensors. This study first applied the algorithm in an apartment in Tianjin, China. The indoor/outdoor contribution to the gross indoor exposure and time-resolved infiltration factor were automatically estimated using the algorithm. The influence of outdoor PM_2.5 data source and algorithm parameters on the estimated results was analyzed. The algorithm was then applied in four other apartments located in Chongqing, Shenyang, Xi'an, and Urumqi to further demonstrate its feasibility. The results provided indirect evidence, such as the plausible explanations for seasonal and spatial variation, to partially support the success of the algorithm used in real apartments. Through the analysis, this study also identified several further development directions to facilitate the practical applications of the algorithm, such as robust long-term outdoor PM_2.5 monitoring using low-cost light-scattering sensors.     

平行坐标技术在干式变压器温度场可视化分析中的应用

本文中笔者将平行坐标技术应用于变压器温度场多维可视化分析,以矿用变压器为例,给出了其高、低压绕组纵向温度分布.     

基于电机效率的纯电动汽车传动系统参数匹配研究

为降低能耗、提高续航里程,本文提出了以提高电机效率为目标的纯电动汽车三档变速传动方案.首先,在分析电机工作特性的基础上提出了三档传动系统参数匹配方法;然后以某纯电动汽车为研究对象,对其驱动系统进行了改动:方案一在不改变原车型动力系统参数的情况下将传动系统由一档改为三档,并运用所提出的方法确定各档位的传动比;方案二在满足整车动力性指标要求下对电机重新选型并匹配三档传动系统;最后利用ADVISOR软件进行NEDC工况仿真分析.结果表明:在不改变原车型动力系统参数的情况下,采用三档传动可使整车的动力性和经济性都有一定的提升,续航里程提高了 9.2％,百公里电耗降低了 1.28 kW·h;重新选型电机后,采用三档传动续航里程提高了 14.1％,百公里电耗降低了 1.87kW·h.     

超亲水毛细芯环路热管启动及热性能分析

为解决电子设备高热通量下的散热问题，采用H₂O₂氧化法对烧结毛细芯进行了超亲水改性，研究了毛细芯表面润湿性对吸液性能的影响。并将改性后的超亲水毛细芯应用到环路热管内，研究了倾斜角度及加热功率对超亲水毛细芯环路热管的换热特性的影响。实验结果表明：超亲水毛细芯的吸液速度增加，吸液时间较亲水毛细芯减小了3.52ms；与普通亲水毛细芯环路热管相比，在加热功率Q=200W时，超亲水毛细芯环路热管蒸发器中心温度降低了约6.0℃，在Q=20W时启动时间与温度分别降低了33s与2.5℃。同时发现超亲水毛细芯环路热管在正重力状态时的运行温度更低，热阻较小，最低热阻仅为0.084℃/W。     

基于6Li+CdTe的新型中子探测器的优化设计研究

面对~3He气体资源严重短缺的国际形势,2018年基于~6Li+CdTe新型中子探测器方案被提了出来,其具备热中子探测效率高、γ灵敏度低及可与~3He气体中子探测器相比拟的特点,有很好的应用前景。本文分析~6Li+CdTe中子探测器的结构和工作原理,采用MCNP6软件对~6Li+CdTe中子探测器进行物理建模并且对其物理性能、结构参数、中子慢化体设计等进行模拟计算,并就该探测器在特殊核材料监测系统中的应用开展了探索研究。结果显示:CdTe吸收层的最佳厚度为10μm;当6层~6Li+CdTe的中子探测单元叠加时,~6Li转化层的最佳厚度为60μm,此时热中子探测效率超过50%;探测系统的尺寸达到4 m×32 cm时,可以满足特殊核物质监测的要求。整个模拟研究获得了探测器最佳工作参数以及辐射监测系统设计方案,对特殊核材料在线中子监测装置的实验研究具有指导意义。     

基于差频检测技术的高速AD单粒子翻转评估方法研究

本文基于差频检测的原理，提出一种在高频动态输入模式下，对高速高精度模数转换器（AD）的抗单粒子翻转效应进行评估的测试方法，并以一款8位3 GSPS高速AD为测试对象，设计开发了一套高速AD单粒子翻转效应测试系统，对目标器件进行了重离子试验。通过对试验结果的图像和错误数据进行分析，评估参试器件的抗辐照性能参数，为抗辐照高速高精度AD的加固设计提供数据支撑。     

职业能力导向下的高职实用性体育课程改革探析——以常州信息职业技术学院为例

现行的高职体育教学多是沿用普通高等学校的课程体系,课程内容并未反映高职教育应有的教育特点,没有很好地发挥体育教学与职业教育相衔接的教学效果.通过职业能力导向下高职实用性体育课程的实施,可以很好地培养学生未来工作岗位所需要的职业体能,提高职业身体素质,从而更好地服务高职教育的发展.